• High cutting efficiency delivers extended tool life and excellent surface finish • Allows higher productivity • Maintains accuracy of grinding wheels over a long time period with reduced down-time and tooling costs, e.g. wheel dressing etc. Minimal mist generation and low viscosity • Improves working environment

Metalworking Fluids/Cutting and Grinding Selection Guide Product DuBois • 3630 East Kemper Road Sharonville, OH 45241‐2011 ‐ For Product Line Assistance: Pam Lazarich 708‐254‐6006 or Kathleen Flynn 708‐496‐4510 Revised: 02/25/2019 ‐ DOCUMENT IS FOR INTERNAL USE ONLY ...

WPS-AGS-016-Cutting Grinding Oil Revision Date 28-Feb-2018 Description of necessary first-aid measures Eye Contact Rinse thoroughly with plenty of water, also under the eyelids. If eye irritation persists, consult a specialist. Skin Contact Wash off immediately with soap and plenty of water. If symptoms persist, call a physician.

The viscosity of cutting oils is typically specified and measured at 40 °C. Some manufacturers test the oil additionally at 100 °C and state the viscosity index. ... turning of hard materials and for grinding processes. Importance of viscosity . Viscosity is important for:

or all users of neat cutting and grinding oils, full implementation of the guidelines for the labelling of mixtures containing mineral oil became obligatory on 1 June 2015. Accordingly, all products with a kinematic viscosity (at 40° C) below 20.5 mm2/s must be labelled with the pictogram GHS08 and the Hazard Statement H304: May

The coolant viscosity should be low enough so the fluid easily floods the grinding zone. Coolant surface tension should be low so grinding swarf can settle and filter out. Before roll grinding begins, any personnel involved in the …

From the results when the depth of cut exceeded 0.1 mm, the oil-based cutting-fluid grinding showed the lowest temperature rise. This result indicates that conventional oil-based cutting-fluid grinding has an advantage over cooling-air and minimum-quantity lubricant application in terms of temperature rise control for large depths of cut.

Moreover, the grinding machine enables the determination of the geometry and the reference of the part with the help of a 3D-probe. The workpieces were cutting inserts made of cemented carbide of the type SNMA120408. As cooling lubricant, grinding oil of MKU-Chemie GmbH, Rödermark, Germany, with a viscosity of 7.6 mm2/s at 40 C was used ...

CUTTING & GRINDING FLUID XTREME KUT 735 . Swiss Style Screw Machine Oil . Performance Benefits . High stock removal in . demanding operations . provided by very good . boundary and EP lubrication Superior tool life . Very good oxidative stability . Low foaming performance . Low Viscosity provides good . cooling and lubricant . penetration at ...

Mineral oil-base cutting fluids, when used to machine aluminum alloys, are frequently cut back to increase their viscosity so as to obtain good cooling characteristics and to make them flow easily to cover the tool and the work. For example, a mineral-fatty oil or a mineral plus a sulfurized fatty oil can be cut back by the addition of as much ...

coolants for grinding operations involving high rates of metal removal. At the other end of the scale, high viscosity mineral oils have low thermal conductivity and are most suited to slow-speed cutting operations involving high contact pressures. Cooling is also related to flowrate. Thus by increasing the flowrate of a cutting oil over the

Jz-lm05 refrigerant is modified by water-soluble diol and refined by adding corrosion inhibitor, mould inhibitor and solubilizer. Its effective composition is more than 85% and its appearance is light transparent liquid. Its specific gravity is 1.04g/cm3, specific heat is 0.58calg ℃ (20 ℃), viscosity is 16.0cp (20 ℃), boiling point is 185 ...

SKY WAX Series. Has been used for a long time in grinding, lapping and polishing processes. Wide variety types are available from high to low Softening point and Viscosity. Good for high precision process. Can not be dissolved by alkaline agents or alcohols well, but Hydrocarbon solvents can clean SKYWAX well. SELECTING CHART.

The cutting fluid type influenced the roughness values. Normally the higher the lubricant ability the lower is the roughness, but in these experiments a high roughness values for the two cutting fluids with high viscosity (cutting oil and the new cutting fluid at …

Cutting fluids contain a wide variety of speciality chemical additives designed to improve lubricity, surface activity, stability and anti-weld properties. (Mortier & Orszulik, 1993) The Chemistry of cutting fluids: a partial overview . When the metal is cut a clean nascent surface at atmospheric pressure results that is very

Viscosity (S.U.S. @ 130°F.) 100 Cutting and Grinding Oil AGS COMPANY P.O. Box 729, Muskegon, MI 49443, U.S.A. Toll Free 800-253-0403 Toll Free in Michigan Canada 800-735-0403 Local Calls (231) 733-2101 FAX (231) 733-1784

Based on the experiment of grinding cemented carbides end mill blade flute with diamond wheels, the effect of the viscosity of total-synthesis cutting oil on grinding process is studied under different feeding speeds and different cut depths. The results of the experiment have shown that grinding with the total-synthesis cutting oil of low viscosity can reduce the grinding force, …

CUTTING & GRINDING FLUID EQO-MAX 714 Low Viscosity Vegetable Based Cutting Fluid EQO-MAX 714 is a vegetable oil-based cutting fluid with superior oxidation resistance. The base stock was carefully chosen for its resistance to thermal and oxidative breakdown even when used in the most rigorous of cutting and grinding applications.

Cutting fluid concentrates are comprised of base oil, esters and fatty acids, emulsifiers, rust ... These are used as grinding fluids. Unlike emulsions, such liquids are entirely soluble in water, and the resultant solution is normally very clear and transparent.

Bright-Cut NHG Metalworking Fluid • Service Classification: Honing/Grinding, Nonstaining • A low viscosity cutting oil that is designed for use in light duty machining or honing and grinding operations on ferrous and nonferrous metals, particularly aluminum, magnesium and their alloys. It can also be mixed with other Bright-Cut

Cutting & Grinding Lubricants. ... Key Features: TechKut FT705 is a moderate viscosity, straight cutting oil designed for machining and forming ferrous metals. TechKut FT705 outperforms other cutting oils and is specifically designed to provide excellent finishes and tool life …

LubeRite EDM 2. 2. Ferrous & Non-Ferrous. For super-tight cutting tolerances, excellent flushing ability. LubeRite EDM 4. 4. Ferrous & Non-Ferrous. For larger cuts, higher voltage cutting. AVAILABLE IN 20 L PAILS AND 200 L DRUMS.

The cut-off grinding force, the mechanical damage and the warp are smaller when using working fluids having low viscosity and excellent osmolarity than that of …

Dionol ® HV 1412 (viscosity 4,0 mm²/s at 40 ° C) Dionol ® HV 1770 is a medium viscous high-performance honing oil optimal for wide diamond and CBN tools when high removal rates and best surface quality should be obtained, as i. e. on modern Sunnen-machines. Analogue to HEDG grinding, excellent lubrication is required.